Easy Load Tray (3 Ramps)

review
5
0
5
Your Price: $892.00
In Stock
Part Number:BIC-1-1-0-1-ELT-1116-3
Easy Load Tray (Three Ramps)


The Easy Load Tray (ELT) uses the transporting Vehicle’s 2” receiver hitch. It lays out flat to load your trike or handcycle from either side with two ramps. Three ramps are available if desired. There are two wheel chocks on the outside wheel trays and tie down straps on all three wheel trays. It folds vertically when unloaded therefore it is not required to remove the Tray when the trike or handcycle is not loaded. 

This is our basic tray system and holds one tadpole type trike, D trike or hand cycle. The trike transporting vehicles 2” receiver hitch must have a ground clearance or 16”. If not, a riser is required to make it so. If a riser is required then it must also have a second Hitch Tite to secure it from moving.

The ELT comes with running and brake lights as well as turn signals. Power to the lights is supplied through either a flat four pin or a round seven blade connector. Easy Load will install either so as to match the trike transporting vehicle.

The ELT is lightweight and easy to handle at ~36 pounds as 10 of the 13 pieces are aluminum. The 2” Receiver Hitch Insert and Wheel Chocks are made from steel. The aluminum pieces consist of 1 Center Tube, L and R Sides, one Front Piece, one Light Bar, three Wheel Channels with grip tape and two Ramps with grip tape. Three Ramps are available. The Ramps and Wheel Channels are ~3” wide. The RHI and Wheel Chocks are made of steel. The Wheel Chocks are fitted with nylon straps and buckles to secure the two wheels of a trike and the center Wheel Channel is fitted with a third strap and buckle to secure the single wheel of the trike. The Center Tube is also used as a conduit for wiring to the lights. Basic usable space to carry a trike is ~36.5” front to back and the Wheel Channels are 63”.long. The effective width, L to R, may be increased by manipulating placement of the Wheel Channels. Moving the center Wheel Channel 6” to the L or R and the outside Wheel Channels 6” the opposite direction will effective ly increase the width by 12”.

The ELT, when a trike is not loaded, rotates to vertical to be out of the way when the vehicle is parked. The ELT rotates on a 3/8” Clevis Pin and is held safely in either vertical or horizontal position with an additional 3/8” clevis pin. It is important to note when lowering the ELT to horizontal the safety pin must be inserted before the trike is loaded as the heavier trikes may make the ELT sag just a bit and inserting the safety pin may not be possible. A second safety feature of the Easy Load Tray is a gravity lock when rotated to vertical. When the triker rotates the ELT to vertical, it will drop about ~1/2” to assure it will not fall to the horizontal position. The safety pin must also be reinserted as a secondary feature to keep the ELT vertical.

The trike can be loaded from either side as the Wheel Channels are “ambidextrous” and the Wheel Chocks can be placed on either the left or right side to facilitate loading from either side to best fit the customer needs. 


*Is your trike running on fat tires? Check out the Easy Load Tray-XL here which has ramps a full 5 inches wider to accommodate wider tires!
Note: The bottom of the 2" receiver hitch must be at least 16" above the ground. If it is not, a riser will be required. We can provide a recommendation for the appropriate riser.

If a riser is required for the transporting vehicle to assure the 16" hitch clearance, a smaller Hitch Tite is required for the riser shaft where it connects to the trike transporting vehicle. Click here for Small Hitch Tite.


IMPORTANT NOTICE: Please be sure to email or call us prior to placing your order to ensure that your vehicle can properly secure an Easy Load Tray. A $50 cancellation fee will be applied to your refund upon order cancellation. Bend It Cycling will contact you regarding shipping costs after order is placed. Depending on your delivery address, Shipping costs typically range between $75 and $105 for orders shipped within the US.
5 Stars
None
Works well. I highly recommend it. Don’t need third ramp. Seems to work just fine or maybe better with 2 ramps.
Did you find this helpful?  3 of 3 Found Helpful
Reviewed by:  from Concord Twp. on 7/16/2022
5

Related Items